Download and Read Furuno Service Manual Fr 2825 Furuno Service Manual Fr 2825 How a simple idea by reading can improve you to be a successful person? View and Download Furuno FR-7040D operator's manual online. Marine Radar Furuno FR-7062 Installation Manual (35 pages) Marine Radar Furuno FR-7111 Operator's Manual.

• Yo u r L o c a l A g e n t / D e a l e r 9 - 5 2, A s h i h a r a - c h o, N i s h i n o m i y a, J a p a n Te l e p h o n e: 0 7 9 8 - 6 5 - 2 111 Te l e f a x. • This is possible — Ask Serious injury or death can result if some- your FURUNO representative or dealer to one falls from the radar scanner mast.

Provide this feature. Turn off the power at the mains switch- board before beginning the installation. • CAUTION WARNING Be sure that the power supply is Ground the equipment to prevent electrical shock and compatible with the voltage rating of mutual interference.

The equipment. Connection of an incorrect power supply Observe the following compass safe can cause fire or equipment damage. The distances to prevent deviation of a voltage rating of the equipment appears magnetic compass. • TABLE OF CONTENTS EQUIPMENT LISTS... Iv SYSTEM CONFIGURATION...

Vi SCANNER UNIT Mounting Considerations, Precautions..1 Mounting Methods...1 Fixing Holes in Mounting Platform..1 Fastening the Radiator to the Radiator Bracket.. 2 Mounting the Scanner Unit...

2 Connecting the Signal Cable... • EQUIPMENT LISTS Standard Supply s t r t s i, e l, e l l l a i t a, e l, e l s t r. • Optional Supply i f i, r e, r e t l i t l i. • SYSTEM CONFIGURATION SCANNER UNIT XN12A-RSB-0070-059 XN13A-RSB-0070-059 XN12A-RSB-0073-059 Signal Cable MJ-B24LPF0005 (10 m, 15 m, 20 m, 30 m, 10 m standard) Radar Plotter Auto Plotter RP-110 ARP-10 (built in display unit) Gyro Gyrocompass Converter DISPLAY UNIT AD-100 RDP-122 Heading Sensor C-2000 PG-2000 Rectifier. • SCANNER UNIT • Do not paint the radiator aperture, to en- Mounting Considerations, sure proper emission of the radar waves. Precautions • When this radar is to be installed on larger • The scanner unit is generally installed ei- vessels, consider the following points: ther on top of the wheelhouse or on the ra- •.

• Fastening the Radiator to the Mounting the Scanner Unit Radiator Bracket The scanner unit can be mounted using the fixing holes on the outside (200 x 200 mm) For your reference, scanner installation ma- or inside (140 x 150 mm) the scanner unit. Terials list appears on page A-8. Prepare ground point in mounting platform CAUTION (within 300 mm of ground terminal on scannere unit) using M6 x 25 bolt, nut and flat washer. Do not lift the antenna unit by the radiator; lift it by the housing.

Julian`s Happy Place - Stormy Glenn - M/m. Loosen four scanner bolts to open the Connecting the Signal Cable scanner unit. Refer to Figure 11 for location. Only the signal cable runs from the display unit to the scanner unit.

In order to minimize the chance of picking up electrical interfer- Upper chassis Hex. Pass the signal cable through the cable Bolt protector. Cable 4-M4 X 16 protector Plate Gasket Flat washer Figure 13 Passing the signal cable through Figure 16 Scanner unit chassis, the cable gland assembly cover opened 5. Fasten the crimp-on lug on the shield to 9. • DISPLAY UNIT Mounting Considerations Tabletop Mounting 1.

Unfasten the two bolts at the front of the The display unit can be mounted on a table- display unit to dismount the mounting top, a bulkhead or on the overhead. When se- base. • Bulkhead, Overhead Mounting The display unit is shipped ready for mounting on a tabletop.

However, it may also be mounted on a bulkhead or on the overhead, following the illustration below. M10 hex bolt, spring washer, flat washer Fixing plate Mounting base M8 x 40 hex bolt (2 pcs.) • WIRING All wiring are terminated at the rear of the display unit. Connect the scanner unit, power supply and external equipment, referring to the drawing below for connector location.

Be sure to ground the display unit. CAUTION Use the power cable supplied with the radar. • ADJUSTMENTS, INITIAL SETTINGS 5. Select menu item with the trackball and Adjustments, Initial Settings press the [ACQ/ENTER] key.